|
|
|
|
|
首頁 >>> 產品目錄 >>> 日本北陽HOKUYO
|
|
產品[北陽UST-05LN/05LA光電開關]資料
|
如果您對該產品感興趣的話,可以
產品名稱:
北陽UST-05LN/05LA光電開關
產品型號:
產品展商:
日本北陽
簡單介紹
北陽UST-05LN/05LA光電開關
電源電壓：10 to 30V
檢測距離：5m
反應時間：66ms
原裝正 品北陽UST-05LN/05LA光電開關
|
|
北陽UST-05LN/05LA光電開關的詳細介紹
|
|
北陽UST-05LN/05LA光電開關
|
Product name
|
Scanning Laser Range Finder
|
|
Model
|
UST-05LN/UST-05LA
|
|
Supply voltage
|
DC 12V/DC 24V (operation range 10 to 30V, ripple within 10%)
|
|
Supply current
|
150mA (DC 24V) or less (during start up about 400mA is necessary.)
|
|
Light source
|
Laser semiconductor (905nm), Laser class 1(IEC60825-1:2007, Accession number:1420210-000)
|
|
Detection range and object
|
60mm to 5000mm (white Kent sheet)
60mm to 2000mm (diffuse reflectance 10% )
Minimum detectable size 130mm (changes according to distance)*1
|
|
Accuracy
|
60mm to 5000mm ±40mm*2
|
|
Standard deviation
|
σ<20mm*2
|
|
Scan angle
|
270°
|
|
Scan speed
|
25msec25ms (motor speed 2400rpm)
|
|
Angular resolution
|
0.5°
|
|
Start up time
|
Within 10 sec (start up time differs if malfunction is detected during start up)
|
|
Outputs
|
Photo-coupler, open collector output Max DC 30V 50mA
Output 1: Output 1 OFF during object detection
Output 2: Output 2 OFF during object detection
Output 3: Output 3 OFF during object detection
Malfunction output: ON during normal operation, OFF during malfunction Synchronization output: Synchronization signal during Master/Slave operation. Note: Output 1 to 3 are switched OFF during malfunction state
|
|
Inputs
|
Photo-coupler, common anode, power supply is 4mA when input is ON Input 1 to 5: Area switching inputs (refer Table1) Synchronization input: Input synchronization signal during Slave operation.
|
|
Output response time*3
|
OFF : 66msec to 3241msec
ON : 66msec to 3241msec
|
|
Hysteresis
|
Hysteresis high (6.25%, not less than 60mm)
Hysteresis low (3.125%, not less than 30mm)
No Hysteresis (Default)
|
|
Interface
|
USB/RS422(UST-05LA only)
|
|
LED display
|
Blue LED: ON during normal operation,
blink during the start up,
Orange LED 1: Output 1 ON during object detection
Orange LED 2: Output 2 ON during object detection
Orange LED 3: Output 3 ON during object detection
|
|
Synchronization function
|
Synchronization Master/Slave operation mode (can set by using Area Designer)*4
Synchronization slave mode (0°)
Synchronization slave mode (90°)
Synchronization slave mode (180°)
Synchronization slave mode (270°)
|
|
Surrounding intensity
|
Less than 15,000lx
Note : Avoid direct sunlight or other illumination sources as it may cause sensor malfunction
|
|
Ambient temperature humidity
|
-10°C to +50°C, below 85%RH (without dew, frost)
|
|
Storage temperature humidity
|
-30°C to +70°C, below 85%RH (without dew, frost)
|
|
Vibration resistance
|
10 to 55Hz double amplitude of 1.5mm for 2hrs in each X, Y, and Z direction
55 to 200Hz 98m / s2 sweep of 2min for 1hr in each X,Y and Z direction
|
|
Shock resistance
|
196m/s2 (20G) X,Y and Z direction 10 times.
|
|
Insulation resistance
|
10MΩ, DC 500V
|
|
Protective structure
|
IP65
|
|
EMC standards
|
(EMI)
EN61326-1：2013
EN55011：2009 + A1：2010
(EMS)
EN61326-1:2013
EN61000-4-2:2009
EN61000-4-3:2006 + A1：2008 + A2：2010
EN61000-4-4:2012
EN61000-4-6:2009
EN61000-4-8:2010
|
|
Weight
|
130g
|
|
Material
|
Front case: Polycarbonate, Rear case: Aluminum
|
|
Dimensions (W×D×H)
|
50×50×70mm
|
*1. In the case of installing the sensor parallel to the Emitter/Receiver surface. Minimum detectable size of the object can be set by Area Designer.
*2. Under the factory standard testing condition using white Kent sheet.
*3. Initial setting is 66msec. ON/OFF delay function switching is possible by Area Designer. Response time can be further delayed by a maximum of 1scan during the area switching.
*4. Initial setting is synchronization master. When using synchronization operation, refer to section 5.3 for details about synchronization wiring. Synchronization slave setting is possible using Area Designer.
公司簡介：
深圳市創豐儀器儀表有限公司是一家專業從事進口自動化產品代理銷售及系統集成的高新技術商貿企業,位于深圳市寶安寶源路廣福大廈（寶安互聯網基地旁）
主營品牌有:azbil,takex,keyence,omron,sunx,fotek,honeywell,banner,moujen,toho等知名品牌.長期以來，創豐公司以多年的行業經驗、充足的貨源、優惠合理的價格、良好的商業信譽、優 質.快捷的服務、再配合具有國際知名度的品牌，已將所代理的產品廣泛應用在全 國各地的冶金，化工，機械，電子,包裝，數控機床,熱處理,紡織機械,輕工、食品包裝、家電等行業，并贏得廣大用戶的高度信賴與好評,建立起良好長久的合作關系。
深圳市創豐儀器儀表有限公司
深圳市寶安區寶源路廣福大廈1003
|
|
|
|
